Anish Rivets LLP

The solid rivet is the most widely used mechanical fastener in construction and manufacturing assembly. It offers the user these advantages:

• Its cost is low
• It allows high rate of production with minimal investment in machinery.
• It facilitates joining different materials of differing thicknesses.
• It has high shear strength.
• It is consistently applied by unskilled labor.
• It provides a tamper-resistant permanent joint.
• It is versatile – can be structural yet decorative.

The solid rivet is the most widely used mechanical fastener in construction and manufacturing assembly. It offers the user these advantages:

• Its cost is low
• It allows high rate of production with minimal investment in machinery.
• It facilitates joining different materials of differing thicknesses.
• It has high shear strength.
• It is consistently applied by unskilled labor.
• It provides a tamper-resistant permanent joint.
• It is versatile – can be structural yet decorative.

The solid rivet is the most widely used mechanical fastener in construction and manufacturing assembly. It offers the user these advantages:

• Its cost is low
• It allows high rate of production with minimal investment in machinery.
• It facilitates joining different materials of differing thicknesses.
• It has high shear strength.
• It is consistently applied by unskilled labor.
• It provides a tamper-resistant permanent joint.
• It is versatile – can be structural yet decorative.

Blind rivets, also known as pop rivets, are tubular and are supplied with a mandrel through the center. The rivet assembly is inserted into a hole drilled through the parts to be joined and a specially designed tool is used to draw the mandrel into the rivet. This expands the blind end of the rivet and then the mandrel snaps off. These types of blind rivets have non-locking mandrels and are avoided for critical structural joints because the mandrels may fall out, due to vibration or other reasons, leaving a hollow rivet that will have a significantly lower load carrying caability than solid rivets. Furthermore, because of the mandrel they are more prone to failure from corrosion and vibration. Unlike solid rivets, blind rivets can be inserted and fully installed in a joint from only one side of a part or structure, “blind” to the opposite side

Blind rivets, also known as pop rivets, are tubular and are supplied with a mandrel through the center. The rivet assembly is inserted into a hole drilled through the parts to be joined and a specially designed tool is used to draw the mandrel into the rivet. This expands the blind end of the rivet and then the mandrel snaps off. These types of blind rivets have non-locking mandrels and are avoided for critical structural joints because the mandrels may fall out, due to vibration or other reasons, leaving a hollow rivet that will have a significantly lower load carrying caability than solid rivets. Furthermore, because of the mandrel they are more prone to failure from corrosion and vibration. Unlike solid rivets, blind rivets can be inserted and fully installed in a joint from only one side of a part or structure, “blind” to the opposite side

Blind rivets, also known as pop rivets, are tubular and are supplied with a mandrel through the center. The rivet assembly is inserted into a hole drilled through the parts to be joined and a specially designed tool is used to draw the mandrel into the rivet. This expands the blind end of the rivet and then the mandrel snaps off. These types of blind rivets have non-locking mandrels and are avoided for critical structural joints because the mandrels may fall out, due to vibration or other reasons, leaving a hollow rivet that will have a significantly lower load carrying caability than solid rivets. Furthermore, because of the mandrel they are more prone to failure from corrosion and vibration. Unlike solid rivets, blind rivets can be inserted and fully installed in a joint from only one side of a part or structure, “blind” to the opposite side

Blind rivets, also known as pop rivets, are tubular and are supplied with a mandrel through the center. The rivet assembly is inserted into a hole drilled through the parts to be joined and a specially designed tool is used to draw the mandrel into the rivet. This expands the blind end of the rivet and then the mandrel snaps off. These types of blind rivets have non-locking mandrels and are avoided for critical structural joints because the mandrels may fall out, due to vibration or other reasons, leaving a hollow rivet that will have a significantly lower load carrying caability than solid rivets. Furthermore, because of the mandrel they are more prone to failure from corrosion and vibration. Unlike solid rivets, blind rivets can be inserted and fully installed in a joint from only one side of a part or structure, “blind” to the opposite side

A rivet is a permanent mechanical fastener. Before being installed, a rivet consists of a smooth cylindrical shaft with a head on one end. The end opposite the head is called the tail. On installation, the deformed end is called the shop head or buck-tail

A rivet is a permanent mechanical fastener. Before being installed, a rivet consists of a smooth cylindrical shaft with a head on one end. The end opposite the head is called the tail. On installation, the deformed end is called the shop head or buck-tail

A rivet is a permanent mechanical fastener. Before being installed, a rivet consists of a smooth cylindrical shaft with a head on one end. The end opposite the head is called the tail. On installation, the deformed end is called the shop head or buck-tail.

A rivet is a permanent mechanical fastener. Before being installed, a rivet consists of a smooth cylindrical shaft with a head on one end. The end opposite the head is called the tail. On installation, the deformed end is called the shop head or buck-tail.

A rivet is a permanent mechanical fastener. Before being installed, a rivet consists of a smooth cylindrical shaft with a head on one end. The end opposite the head is called the tail. On installation, the deformed end is called the shop head or buck-tail.

• We are engaged in offering a wide range of quality products to our clients. Our range of all products is widely appreciated by our clients.

• We are engaged in offering a wide range of quality products to our clients. Our range of all products is widely appreciated by our clients.

Minimum order quantity: 1000 Piece

• We are engaged in offering a wide range of quality products to our clients. Our range of all products is widely appreciated by our clients.

These are 2 piece Rivets.
one is a semi-tubular rivet and other is a blind rivet.

Semi-tubular rivets (also known as hollow rivets) are similar to solid rivets, except they have a partial hole (opposite the head) at the tip. The purpose of this hole is to reduce the amount of force needed for application by rolling the tubular portion outward. The force needed to apply a semi-tubular rivet is about 1/4 of the amount needed to apply a solid rivet. Tubular rivets can also be used as pivot points (a joint where movement is preferred) since the swelling of the rivet is only at the tail. Solid rivets expand radially and generally fill the hole limiting movement.

The solid rivet is the most widely used mechanical fastener in construction and manufacturing assembly. It offers the user these advantages:

• Its cost is low
• It allows high rate of production with minimal investment in machinery.
• It facilitates joining different materials of differing thicknesses.
• It has high shear strength.
• It is consistently applied by unskilled labor.
• It provides a tamper-resistant permanent joint.
• It is versatile – can be structural yet decorative.

Semi-tubular rivets (also known as hollow rivets) are similar to solid rivets, except they have a partial hole (opposite the head) at the tip. The purpose of this hole is to reduce the amount of force needed for application by rolling the tubular portion outward. The force needed to apply a semi-tubular rivet is about 1/4 of the amount needed to apply a solid rivet. Tubular rivets can also be used as pivot points (a joint where movement is preferred) since the swelling of the rivet is only at the tail. Solid rivets expand radially and generally fill the hole limiting movement.

• We provide hole depth as per the dimensions provided.
• If no details are provided then we manufacture rivets in accordance to the maximum hole depth as defined by Bureau of Indian Standards.

A rivet is a permanent mechanical fastener. Before being installed, a rivet consists of a smooth cylindrical shaft with a head on one end. The end opposite the head is called the tail. On installation, the deformed end is called the shop head or buck-tail

A rivet is a permanent mechanical fastener. Before being installed, a rivet consists of a smooth cylindrical shaft with a head on one end. The end opposite the head is called the tail. On installation, the deformed end is called the shop head or buck-tail

A rivet is a permanent mechanical fastener. Before being installed, a rivet consists of a smooth cylindrical shaft with a head on one end. The end opposite the head is called the tail. On installation, the deformed end is called the shop head or buck-tail.

• We are engaged in offering a wide range of quality products to our clients. Our range of all products is widely appreciated by our clients.

• We are engaged in offering a wide range of quality products to our clients. Our range of all products is widely appreciated by our clients.

This rivets has an additional step between head and body.
This product can be with or without hole

2 piece male-female rivets are non-structural fastening rivets fo grip applications.

To install 2 piece rivets, access to both sides of the work piece is required.

The tubular component is inserted from one side, and the rivet itself is inserted from the opposite side.

Minimum order quantity: 100000 Piece

MS OHPT Rivets specially for PP boxes.
Used for riveting using precision automatic Machines

Semi-tubular rivets (also known as hollow rivets) are similar to solid rivets, except they have a partial hole (opposite the head) at the tip. The purpose of this hole is to reduce the amount of force needed for application by rolling the tubular portion outward. The force needed to apply a semi-tubular rivet is about 1/4 of the amount needed to apply a solid rivet. Tubular rivets can also be used as pivot points (a joint where movement is preferred) since the swelling of the rivet is only at the tail. Solid rivets expand radially and generally fill the hole limiting movement.

• We provide hole depth as per the dimensions provided.
• If no details are provided then we manufacture rivets in accordance to the maximum hole depth as defined by Bureau of Indian Standards.

Semi-tubular rivets (also known as hollow rivets) are similar to solid rivets, except they have a partial hole (opposite the head) at the tip. The purpose of this hole is to reduce the amount of force needed for application by rolling the tubular portion outward. The force needed to apply a semi-tubular rivet is about 1/4 of the amount needed to apply a solid rivet. Tubular rivets can also be used as pivot points (a joint where movement is preferred) since the swelling of the rivet is only at the tail. Solid rivets expand radially and generally fill the hole limiting movement.

• We provide hole depth as per the dimensions provided.
• If no details are provided then we manufacture rivets in accordance to the maximum hole depth as defined by Bureau of Indian Standards.

Semi-tubular rivets (also known as hollow rivets) are similar to solid rivets, except they have a partial hole (opposite the head) at the tip. The purpose of this hole is to reduce the amount of force needed for application by rolling the tubular portion outward. The force needed to apply a semi-tubular rivet is about 1/4 of the amount needed to apply a solid rivet. Tubular rivets can also be used as pivot points (a joint where movement is preferred) since the swelling of the rivet is only at the tail. Solid rivets expand radially and generally fill the hole limiting movement.

• We provide hole depth as per the dimensions provided.
• If no details are provided then we manufacture rivets in accordance to the maximum hole depth as defined by Bureau of Indian Standards.

Semi-tubular rivets (also known as hollow rivets) are similar to solid rivets, except they have a partial hole (opposite the head) at the tip. The purpose of this hole is to reduce the amount of force needed for application by rolling the tubular portion outward. The force needed to apply a semi-tubular rivet is about 1/4 of the amount needed to apply a solid rivet. Tubular rivets can also be used as pivot points (a joint where movement is preferred) since the swelling of the rivet is only at the tail. Solid rivets expand radially and generally fill the hole limiting movement.

• We provide hole depth as per the dimensions provided.
• If no details are provided then we manufacture rivets in accordance to the maximum hole depth as defined by Bureau of Indian Standards.

A rivet is a permanent mechanical fastener. Before being installed, a rivet consists of a smooth cylindrical shaft with a head on one end. The end opposite the head is called the tail. On installation, the deformed end is called the shop head or buck-tail.

A rivet is a permanent mechanical fastener. Before being installed, a rivet consists of a smooth cylindrical shaft with a head on one end. The end opposite the head is called the tail. On installation, the deformed end is called the shop head or buck-tail.

A rivet is a permanent mechanical fastener. Before being installed, a rivet consists of a smooth cylindrical shaft with a head on one end. The end opposite the head is called the tail. On installation, the deformed end is called the shop head or buck-tail.

• Standard Size FH Solid Rivets
• We are engaged in offering a wide range of quality products to our clients. Our range of all products is widely appreciated by our clients.

A rivet is a permanent mechanical fastener. Before being installed, a rivet consists of a smooth cylindrical shaft with a head on one end. The end opposite the head is called the tail. On installation, the deformed end is called the shop head or buck-tail.

• We are engaged in offering a wide range of quality products to our clients. Our range of all products is widely appreciated by our clients.

• We are engaged in offering a wide range of quality products to our clients. Our range of all products is widely appreciated by our clients.

• We are engaged in offering a wide range of quality products to our clients. Our range of all products is widely appreciated by our clients.

For plastic and paper files